PE Civil Construction Practice Exam

These questions are part of the practice quiz. Start practicing

• What is the main function of scheduling software in project management?
• What is a contingency plan in a construction project?
• What is the primary purpose of a cofferdam?
• In the formula γ = Sg x γw, what does γ represent?
• What is the difference between heaped and struck capacity in measurement?
• What is the primary purpose of a construction schedule?
• In construction bidding, what is a bid alternative?
• Which manual addresses load combinations including environmental loads in construction?
• What is site grading primarily concerned with?
• When is it appropriate to use a mat foundation instead of a pile foundation?
• What is the significance of a geotechnical report in construction?
• The area of a trapezoid can be calculated using which formula?
• What is meant by "overhead" in construction costs?
• What is the conversion factor from miles to feet?
• What factors are considered in pavement design?
• In project management, which technique is used to compensate for lost time?
• What is the primary unit of measurement used in earthwork calculations?
• What are wales in the context of formwork?
• What does "mean grain size" refer to in geology?
• How is weight calculated in structural engineering?
• Which component of risk assessment involves determining the potential consequences of a risk event?
• What are Deadman in construction terminology?
• What typically influences the mean grain size in soil analysis?
• What is another term for an isolated footing?
• What is a value engineering proposal aimed at achieving?
• Which aspect of scheduling is primarily affected by weather conditions according to the construction practices?
• What is typically included in the risk evaluation phase?
• What is the primary role of a project estimator in construction?
• Which property distinguishes a one-way slab from a two-way slab?
• How many feet of water correspond to 1 psi?
• What characterizes a Unit Price contract?
• What purpose do dummy activities serve in scheduling?
• What do the limits of excavation for a contractor define?
• In construction management, what do the three main resources usually refer to?
• Which characteristic is key in determining the yield of a batch?
• What ratio defines a one-way slab in contrast to two-way slabs?
• When is a strip footing, also known as a continuous footing, primarily used?
• In terms of project performance measurement, what does a schedule baseline help assess?
• What is the formula for the Load Factor (LF)?
• What characterizes a free outlet in hydraulic engineering?
• What does the federal acquisition regulation (FAR) govern?
• Which method can improve soft soils to reduce long-term settlement?
• What does the specific weight of water measure?
• Why is linear scheduling important in project management?
• How many pounds are in one sack of cement?
• Which of the following methods is NOT used to improve soft soils?
• What is the equivalent flow rate of 1 million gallons per day in cubic feet per second (cfs)?
• What equation is not included in vertical curve calculations?
• What is the specific weight of water in metric units?
• What is a 'request for information' (RFI) in construction?
• What term refers to the total value of construction work under contract?
• Which of the following describes a zero force member in structure analysis?
• What is the value of acceleration due to gravity in imperial units?
• How does earned value management (EVM) aid in project management?
• What is the primary goal of risk assessment in construction?
• What does 'mobilization' refer to in a construction context?
• A contract type where the scope of work and price are agreed upon beforehand is called?
• Which of the following is NOT typically included in a construction scope statement?
• Which contract type sets a specific maximum charge for the contractor, intended for projects with known challenges?
• In construction, what does the term "falsework" refer to?
• How can hazard identification contribute to better construction outcomes?
• Which of the following best describes a load-bearing wall?
• What does the load factor refer to in structural engineering?
• In a standard penetration test, how is the N value determined?
• When analyzing conditions, what should you look for as "not true"?
• What is the friction angle (φ) value of clay?
• What does the term "crashing" refer to in project management?
• How many square feet are there in one acre?
• What happens when both members of a 2-member joint have no external forces?
• Which unit is used to express the density of water in imperial units?
• How many pounds of force are equivalent to 1 kip?
• How do weather factors typically affect construction schedules?
• What type of information does as-built documentation provide?
• What is the correct ratio of concrete to sand to coarse aggregate in a concrete mixture?
• Which of the following is a characteristic of a pile cap?
• What is the purpose of underpinning in construction?
• What components make up a standard concrete mix ratio?
• Addenda in construction documents serve what purpose?
• What does the term 'specific gravity' refer to in material science?
• What kind of scheduling technique is used to manage resources on a construction site?
• What role does risk analysis play in the construction industry?
• What is the atmospheric pressure in metric units?
• What is meant by dead storage in the context of a detention pond?
• Which term refers to the agreed limits for excavation in a project?
• What is the atmospheric pressure in imperial units?
• In concrete testing, which manual is recommended for reference?
• Which of the following is a characteristic of a strip footing?
• Which of the following words should you look for when interpreting questions?
• What is a design build delivery method?
• How should 1 kN be interpreted when making calculations?
• What is the purpose of an environmental remediation process?
• When determining if a question involves active or passive Rankine earth pressures, what aspect is primarily evaluated?
• What does “value engineering” aim to achieve in a project?
• Which of the following is NOT an essential component of risk assessment in construction?
• How should fill and cut volumes be calculated?
• In horizontal curves, which equations are excluded from calculations?
• What is the significance of building codes in construction?
• How many gallons per minute (GPM) are equivalent to 1 ft/s³?
• What occurs during the project closeout phase?
• Does hydrostatic pressure receive a Rankine earth coefficient?
• What does the suffix "g" represent in scientific notation?
• What does the term "site layout" refer to in construction?
• What does ppm stand for in environmental science?
• What are diaphragm walls commonly used for in construction?
• Which footing is primarily used in a situation involving closely spaced columns?
• What factor must be considered when designing a foundation in soft soil?
• What is the main difference between a fixed-price contract and a cost-plus contract?
• Which of the following best describes risk evaluation in construction?
• What is the value of acceleration due to gravity in metric units?
• How much does one gallon of water weigh?
• How does sustainability influence construction practices?
• Which type of footing is not recommended for an array of columns?
• Why is effective scheduling important in construction?
• How much does water weigh in imperial units?
• What role do weighted blocks, referred to as Deadman, serve in construction?
• What does the acronym “OSHA” stand for?
• Which of the following corresponds to standard atmospheric pressure in metric units?
• When comparing earth materials, what is critical to consider in determining their densities?
• What does specific gravity (γ) refer to in construction materials?
• Why is a schedule baseline crucial for construction project management?
• Which manual outlines health and safety regulations relevant to construction practices?
• What purpose does a pile cap serve in construction?
• How many cubic feet are in one gallon?
• Which aspect is essential when surveying large parcels?
• What does the term "construction loads" encompass?
• What is the purpose of tieback anchors in construction?
• What is the primary purpose of a schedule baseline in construction projects?
• What is meant by the "yield of a batch" in construction?
• What is the specific weight of water in imperial units?
• How can a construction lien be defined?
• What is the main role of a construction manager?
• How do you solve the equation log(x) = y for x?
• Which documents are typically included in a construction cost estimate?
• Which of the following best describes the process of changing project documents before signing?
• Which additional manuals are used for structural questions regarding formwork and construction loads?
• When may a Lump Sum contract be least economical?
• In which contract type does the owner pay for material and labor, plus a percentage of the costs as profit, potentially leading to delays?
• What is the function of a Form Tie in concrete construction?
• In what scenario would you utilize a standard penetration test?
• What is the first step in the risk assessment process in construction?
• What is the purpose of an environmental impact assessment?
• How is the term "tailwater" used in hydraulic engineering?
• What type of contract is characterized by payments based on material price and labor per hour, suitable for projects with indeterminate scope?
• What is the main difference between concurrent and sequential tasks in scheduling?
• What is project management software primarily designed to do?
• What is a typical use case for isolated footings?
• What is the primary purpose of performing separate calculations for fill and cut?
• How is a one-way slab defined?
• Which of the following is true about the weight of a solid material?
• What is the primary consequence of overextending a Lump Sum contract?
• What responsibility does a general contractor hold during a construction project?
• Which reference manuals are used for temporary structures during construction?
• What is a common outcome of failing to manage construction risks effectively?
• What is the normal weight of concrete in pounds per cubic foot?
• A key factor in calculating earthwork involves taking into account what aspect of the soil?
• What does risk management in construction involve?
• What does a Geodetic Survey take into account?
• What is another name for a mat foundation?
• What is the density of water in metric units?
• What is a potential impact of adverse weather on resource allocation in construction?
• What is the primary purpose of a detention pond's dead storage?
• What is the typical cohesion value (c) of sand?
• In earthwork calculations, how is the mass of a project related to the mass of the bank?
• What factors contribute to construction site safety?
• What does “BIM” stand for in the construction industry?
• What is the purpose of soil compaction in construction?
• What does the term “punch list” refer to in construction?
• Which structural member is crucial for providing lateral support in formwork?
• What is the relationship of psi to feet of water head?
• Which project management technique is used to determine the longest sequence of dependent tasks?
• What contract type allows the owner to cover material and labor costs plus a fixed profit amount, incentivizing efficiency?
• What function cancels out the natural logarithm (ln)?
• What describes a cement bag's weight in pounds?
• What does 'LEED certification' signify?
• What does "crashing" usually involve?
• According to ASCE 37-14, is it permissible for equipment and personnel to be on sloping roofs?
• Why is quality control critical in construction?
• What is the specific gravity (Gs) of Portland cement?
• What is the purpose of safety data sheets (SDS) in construction?
• What is headwater in relation to a culvert?
• When is a pile foundation typically used?
• What foundation type is used specifically when the soil has high bearing capacity?
• What property of water does "specific weight" quantify?
• What is a dummy activity in project scheduling?
• What is linear scheduling primarily concerned with?
• What document outlines the responsibilities of parties in a construction project?
• What do performance specifications focus on in construction projects?
• What is one of the key benefits of conducting a thorough risk analysis?
• What does 'lead time' refer to in construction projects?
• What is referred to as the length of overlap required for rebar?
• What unit is standard for measuring concrete compressive strength?
• What is the primary role of form shoring during construction projects?
• What are 'change orders' in a construction contract?
• What might be a direct consequence of not considering weather factors in construction scheduling?
• How is a Form Tie typically used in the construction process?
• What is form shoring used for in construction?
• What are submittals in the context of construction projects?
• When interpreting a question, which term should prompt careful consideration?
• Which of the following is considered one of the three main construction resources?
• What is the original soil volume in its undisturbed state referred to as?
• What are the typical components of a project scope statement?
• What does the term 'subcontractor' refer to in construction?